How do I know if new chimney flashing is installed right?
Homeowners replacing animal-damaged flashing often cannot tell whether a gap underneath is intentional or a spot where water will get in, and what else around the chimney—like a cap or cricket—needs attention. Because what sits beneath a piece can matter and advice conflicts, people hesitate to sign off or push back with contractors before making final payment.
Core Friction Pattern
Analysis of 3 peer accounts across online developer and community forums reveals that “How do I know if new chimney flashing is installed right?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.
+6 alternative community-tested workarounds cataloged below.
What people tried
Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.
Found another way around this?
Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.
How do I know if new chimney flashing is installed right?
- 1Asking on an online home maintenance forum for others to inspect the workDid this help you?
- 2Grinding counter flashing into mortar joints with a reglet cut instead of relying on surface caulking on brickDid this help you?
- 3Using rigid flashing rather than foil-backed tape or trim coilDid this help you?
- 4Replacing the chimney cap and installing a chimney cricketDid this help you?
- 5Holding back final payment and sign-off until checking whether the work needs to be fixedDid this help you?
- 6Gently prying up the bottom edge or removing vertical gasketed fasteners to peek underneath without damaging anythingDid this help you?
- 7Asking the roofers about what is underneath or watching for water ingress during rainfallDid this help you?
In their words
Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.
“Previous overgrown vegetation allowed animals to chew/destroy old led flashing, so I just had new flashing put in - does it look correct? I’m not really sure what to look for”source ↗
“Asking because, I had the same problem when I bought my place. Had to do what you did, and replace the chimney cap, AND install a "cricket".”source ↗
“Is this gap under the chimney flashing intentional? Everything else looks really well done, but wouldn't water just run straight into this gap?”source ↗
“I haven't made final payment yet. I just don't want to complain to the contractors if this is perfectly fine. If it's not, I want them to fix it before I sign off.”source ↗
“Yeah, that's exactly my concern, but it seems some folks are suggesting that it might depend on what's going on underneath that piece.”source ↗
Where this came up
People with this problem also raised
Related community dilemmas clustered by discussion consensus
How to tell if a ridge vent was installed correctly
Roofers sometimes install ridge vents just for appearance without cutting the roof decking underneath, but standard visual checks or endoscope cameras can fail to confirm the cutout. Without knowing if the gap or missing shingle near the end is a defect or normal, homeowners are left guessing whether they need to pay for repairs.
How to tell if worn chimney flashing is leaking
Worn or poorly sealed chimney flashing can hide leaks that eventually cause water to drip into lower levels during heavy rainfall. Because flashing often conceals vulnerable areas—like roof transitions or covered porch ceilings—it is difficult to spot active damage without checking for hidden moisture entry points.
Hollow spots and messed up baseboards after new flooring
Some areas feel hollow underneath and sound different after luxury vinyl plank installation, while laminate ends under walls are sometimes cut and stuck together without clicking. Homeowners want to know if these issues indicate faulty contractor work and what can be done before the crew leaves.
How do I know if my roof leak is actually fixed?
Contractors and property managers often claim a roof leak is repaired without providing proof or letting homeowners know they completed the work, leaving residents skeptical and anxious. Without confirmation, people are left staring at interior water stains and wondering whether it is safe to repaint or if the next storm will bring another leak.
Are open cavity vent returns and exposed pipes normal in new construction?
Open-cavity plenum returns and exposed bathroom pipes are shortcut building methods used to save installation time and material costs. These makeshift setups compromise indoor air quality, create noise issues, and expose plumbing lines to potential damage inside the HVAC pathway.
Do I need to caulk my new shower or was it left unfinished?
Debris and gaps in a new-build shower seal often stem from leftover construction materials rather than a failed seal. Water getting into these small gaps can cause underlying moisture damage if the joints are left unsealed, making it necessary to inspect whether a protective bead of caulk is actually missing.