What people keep running into with engine maintenance
Complaints tagged engine maintenance, each raised by more than one person. One-off posts are not included.
115 recurring problems · 1592 people · 18 forums we read
Raised more than once
Most people first.
- 4Is it safe to drive with a wobbling belt tensioner?A wobbling tensioner assembly and noise that appear specifically when the A/C is active leave drivers questioning whether it is safe to drive or if the part needs immediate replacement. Figuring this out is complicated by the risk of new replacement parts failing, incorrectly sized belts, or worn components that make it difficult to know what needs to be changed.
- 4How to learn car engine repairs like timing chains and flywheelsComplex car repairs require hands-on instruction and guidance from an experienced mechanic, which leads some people to offer to pay a professional to teach them in person. Without direct expert help, DIYers get stuck on unexpected mechanical damage like milled locating pins and flattened dowels, leaving them unsure whether parts need to be drilled out or professionally repaired.
- 4Dropped clip stuck in spark plug holeWhen a part like an injector clip falls into a spark plug hole, it often clips onto the plug with too little room for prying tools to work. The tight clearance bends the tools, and poor visibility makes the debris incredibly difficult to retrieve. This stops people from getting their cars running, often pushing them to consider intentionally breaking the spark plug to free the blockage.
- 4How to check if a used car timing belt was actually changed?Dealers often claim a timing belt has been replaced without providing any invoices or proof, and mechanics may spot unreplaced parts like an old water pump. Because an immediate replacement is too expensive and the car is needed for daily work, owners are left trying to inspect the belt's wear themselves to see if it can safely survive another year.
- 3Is it safe to drive with timing off by two teeth?When engine timing is off by two teeth, it causes a misfire and rough idle that leaves drivers questioning whether they can make a 30-minute drive to the nearest available shop. Attempting the trip risks causing irreversible and more expensive vehicle damage.
- 3Is it safe to reuse a rusty engine intake valve?Rust on the flat surface of a used intake valve leaves many wondering if it will cause engine damage or if it's just too much trouble to trust. Because going through a cylinder head rebuild is a massive effort, rebuilding with questionable used parts risks catastrophic failure and forces many to question whether they should just buy new ones instead.
- 3Why is my car losing oil with no leaks or smoke?Engines can silently consume oil internally through worn piston rings, faulty valve stem seals, or a failing PCV valve that pulls oil directly into the combustion chamber without producing visible blue smoke. This hidden consumption forces drivers to constantly top off fluid levels and risks severe engine damage if the oil drops too low between regular changes.
- 3How to identify unknown debris found in engine oil panFinding unknown fragments or crud during maintenance makes it difficult to know what part is failing or if the engine is at risk of damage. Without knowing the source of the debris, people cannot safely determine whether to repair the component or continue driving.
- 3Grinding noise and burning smell after starter replacementA new starter can cause a loud grinding noise on startup and a burning wiring smell if something was installed incorrectly or a wire like the fusible link is damaged. This leaves the car owner dealing with warning lights and uncertainty about whether the vehicle is safe to drive.
- 3Is it safe to run E15 high-ethanol fuel in an older engine?High-ethanol fuel blends like E15 contain more alcohol than legacy fuel systems and older carburetors can handle. This higher alcohol content attacks and destroys older rubber components throughout the fuel system, including the fuel lines, pump, and carburetor.
- 3What is the hard crust buildup on my oil cap?Unusual hard residue on an oil fill cap is often harmless condensation mixed with oil vapor, but it can sometimes signal a more serious engine issue like a blown head gasket. Because it requires scraping to remove and looks concerning, car owners struggle to determine whether it is normal moisture or a sign of internal engine failure.
- 3How to check if a vibrating radiator is caused by a bad fanNoise and vibration coming from under the hood often stem from a damaged radiator fan assembly, bent blades, or a failing fan motor. If left unverified, a broken or non-running fan can lead to poor engine cooling, potential overheating, and costly engine damage.
- 3Why does coolant overflow from the reservoir and not return?Coolant flows out into the overflow tank as the engine gets hot, but a cooling system leak or air pocket prevents a proper vacuum from forming as the engine cools down. Because the system cannot suck the coolant back into the radiator, the reservoir fills up and spills over while leaving the actual radiator underfilled.
- 3Weird buzzing noise after jump starting a carA buzzing sound often comes from around the radiator fan after a jump start and slows down as the car warms up. This noise can persist and occur right after startup, alongside issues like rough idling.
- 3Cracked engine head while torquing oil pressure sensorOvertightening or stressing the threads while replacing an oil pressure sensor can crack the engine cylinder head, causing persistent oil leaks. While some drivers resort to temporary fixes like epoxy to seal the area, a cracked head ultimately threatens the structural integrity of the engine block and requires a permanent repair or replacement.
- 3How to reach a hidden screw blocked by other car partsWhen replacing components like a power steering o-ring, essential mounting screws are often blocked by surrounding assemblies or tight spaces. This leaves DIYers unable to reach the fastener without removing extra parts they aren't comfortable dismantling, forcing them to abandon simple repairs to avoid breaking something else.
- 3Why is power steering air so hard to bleed out?Purging air from power steering lines after a repair is physically exhausting and repetitive, requiring fast sweeps of the steering wheel. Even after working hard to bleed the system, trapped air causes persistent bubbles in the reservoir and leaves the steering tight and whiny.
- 3How long before an engine fails with worn cam lobes?Running a high-mileage engine with scored cam lobes and worn roller bearings without a full timing job is essentially rolling the dice on its lifespan. Because the truck is old and rusty, paying for a complete repair often exceeds the vehicle's worth, leaving owners unsure how much time is left before it dies.
- 3What extra parts do I need to replace during an engine teardown?When tearing down an engine for a major repair like a head gasket, knowing which extra gaskets, bolts, and internal components to replace preventatively is difficult without prior experience. This leaves people unsure of what else to order or how to properly inspect parts below the lifters and valves before putting the engine back together.
- 3Can't get the serpentine belt back on the alternator pulleyA hose can prevent you from pulling your wrench down far enough to fully loosen the tensioner. Without enough room to release that tension, you cannot slip the intact belt back over the alternator pulley. This prevents you from charging the system and restoring your failing dash displays and power steering.
Comes up alongside
Topics that keep appearing on the same problems — not topics with similar names.