Said It Here

Why do LED lights randomly turn off and on?

LED lights often turn off and back on due to thermal overload or failing drivers that shut down when they overheat. This unexpected cycling cuts out light mid-use and can leave you in the dark until the fixture cools down enough to reset.

OverviewLatest thread: Nov 2026
People affected3 accounts (2 forums)
Workarounds found3 items recorded
Discussion timelineSep 2026 – Nov 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/askanelectrician, r/homeautomation · Sep 2026 – Nov 2026
Verification standards →

Core Friction Pattern

Analysis of 3 peer accounts across online developer and community forums reveals that “Why do LED lights randomly turn off and on?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
Turning off or abandoning problematic automations

+2 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What the numbers show

Counted from the threads quoted below. How we count

  • People have been saying this in most months since September 2026.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Nov 2026)Indexed across peer discussions from Sep 2026 to Nov 2026
Evaluated against breaking changes & deprecations
  1. 1
    Turning off or abandoning problematic automations
    Did this help you?
  2. 2
    Adding timers that reset when new motion is detected
    Did this help you?
  3. 3
    Using physical manual switches instead of automations
    Did this help you?

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/homeautomation2 people · November 2026

“I gave up on motion lights in the hallway after the third time they turned off while I was still in there”source ↗

Difficult_Dot7708 · r/homeautomationNov 2026· 1 upvotes

“I stopped using a turn everything off when I leave automation because it kept deciding I had left when I was still home”source ↗

Greedy-Fun4081 · r/homeautomationNov 2026· 1 upvotes
r/askanelectrician1 person · September 2026

“For some reason it has begun turning off, and then turning back on within 5 minutes.”source ↗

jeeperkeeper · r/askanelectricianSep 2026

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

LED light stays dimly on when smart switch is off

Replacing a standard switch with a smart single-pole switch, like a Lutron Caseta wireless model, does not always turn the bulbs off completely. The connected LED lights remain dimly lit even when the switch is in the off position.

1 workaround2 accounts · 2 forums

Dashboard lights and ABS lights flashing when using turn signal

Activating the turn signal can cause unrelated dashboard lights, center console indicators, and even ABS or traction control lights to flash or turn on unexpectedly. This electrical glitch often points to a shared ground failure or a wiring short circuit in the steering column or tail light assembly.

2 workarounds2 accounts · 2 forums

Light switch sparks and won't stay on

A light switch that sparks and only stays on when flipped very gradually points to a failing internal mechanism or loose wire. This makes normal use a genuine hazard that prevents safe operation of the lights until the switch is replaced or repaired.

4 workarounds3 accounts · 1 forum

Dishwasher lights blinking and won't start

Blinking indicator lights often signal an active error state or incomplete cycle that a standard circuit breaker reset cannot clear. This locks the control panel and stops the dishwasher from running new cycles until the underlying fault code or diagnostic lock is resolved.

8 workarounds3 accounts · 1 forum

Why does my monitor go black when lights turn on?

Turning on light switches, opening doors, or running nearby appliances like a clothes dryer causes computer screens to briefly go black for a few seconds. This sudden blanking leaves users confused and unable to figure out whether the issue stems from faulty cords or an electrical problem.

3 workarounds2 accounts · 2 forums

ABS light stays on after replacing speed sensor and brakes

Replacing the wheel speed sensor, front brakes, rotors, or calipers does not always clear the dashboard warning. The light continues to show after the parts are changed, leaving drivers unsure if the ongoing warning is related to the recent repair.

4 workarounds2 accounts · 2 forums