Water leaking behind new gutters and soffits
Water is following the drip-edge flange downward, hitting the back of the gutter, and dropping straight down the outside instead of flowing inside. This accumulated water collects between the soffit and the lip of the fascia, causing leaks that did not happen before the installation.
Core Friction Pattern
Analysis of 11 peer accounts across online developer and community forums reveals that “Water leaking behind new gutters and soffits” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.
+20 alternative community-tested workarounds cataloged below.
What the numbers show
Counted from the threads quoted below. How we count
- People have been saying this in most months since September 2026.
- This comes up 31.1× more often in r/Roofing than across the site as a whole.
What people tried
Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.
Found another way around this?
Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.
Water leaking behind new gutters and soffits
- 1Putting clear silicone on a cut or seam in the drip edge where water might be leaking.Did this help you?
- 2Trying to adjust the gutter slope or lower the end of the gutterDid this help you?
- 3Sealing the joint between the frame and brick with caulkDid this help you?
- 4Checking for flashing and proper weather barriersDid this help you?
- 5Leaving the gap alone because roof runoff still lands in the gutterDid this help you?
- 6Installing a piece of exterior trim to prevent wasps or critters from nesting in the gapDid this help you?
- 7Cleaning out the gutter completely to see if clogs are backing water up over the edgeDid this help you?
- 8Removing a few courses of siding to install new flashing that sheds water into the gutter instead of behind itDid this help you?
- 9Having the contractor fill the exposed holes and raise the gutters up behind the drip metal.Did this help you?
- 10applying silicone sealant as a temporary patchDid this help you?
- 11installing a drip edge extension to bridge the gapDid this help you?
- 12screwing through the drip edge to hang the gutter higherDid this help you?
- 13Lifting the shingles and getting a new metal drip edge bent to drop directly into the gutter.Did this help you?
- 14Extending the roof out further by running another 3/4 inch of shingle and sealant.Did this help you?
- 15Tucking a piece of flashing behind the drip edge manuallyDid this help you?
- 16Withholding final payment from the contractor until the drainage and pitch are fixedDid this help you?
- 17Calling out a different gutter company for a repair estimate and using that number to negotiate with the original rooferDid this help you?
- 18Checking for blockagesDid this help you?
- 19Spraying water on the roof to testDid this help you?
- 20Trying to reseat the elbow into the downspoutDid this help you?
- 21Calling back the original installersDid this help you?
In their words
Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.
“Pictures 1- 3 are after install after a light rain, standing water in the gutters, water dripping behind the gutters every few inches around the entire house, one corner was leaking and some Drips along a couple downspout.”source ↗
“They went around and hand pulled the drip edge out and it looks terrible, all bent up. He noticed no measuring tapes or laser levels and he asked how they are figuring out the pitch and the owner basically said they have done this so much they are able to eye ball it.”source ↗
“Water is getting behind the gutters in the middle of some of the runs and then leaking out of the 90* corners and end caps.”source ↗
“there is this gap between the drip edge and the gutter itself where I can see straight through to the fascia board”source ↗
“However I had the same issue that you have in photo #2; in spots to accommodate the correct pitch, the back edge of the gutter did not tuck under the drip edge. For those areas, I tucked a piece of flashing behind the drip edge, and that stopped the leaking behind the gutters.”source ↗
“Recently got gutters cleaned and a new downspout installed. Lots of rain last night and I saw this. Can someone help me understand what could be the issue?”source ↗
“I never had dripping like this with the old wood, soffit or fascia.”source ↗
“As soon as I put my finger in the area between the soffit and lip of the fascia, I could feel water accumulating there and upon prodding it dripping started again.”source ↗
“My gutters were reinstalled below the new fascia directly against the siding (vertical T&G).”source ↗
“The project finished a couple weeks ago and now I have water running into the soffit and then rolling down the side of the house and dripping on the window sills.”source ↗
“We've never heard rain consistently running down the siding and dripping on the window sills before.”source ↗
“Any idea how to stop this drip? Pretty significant leak that puddles right by my foundation - looks like it’s right where the siding meets the gutter!”source ↗
“Water follows the drip-edge flange downward (red arrow), hits the back of the gutter, and then drops straight down the outside instead of flowing into the gutter.”source ↗
“It looks like my flashing guy caulked next to the gap but didnt fill the other gap in and I got some water inside over the weekend through my trim around the window.”source ↗
“I just had a new roof and gutters installed. There are some gaps between the gutters and fascia boards. The gaps are not uniform as some areas are wider than others. Is this normal?”source ↗
Where this came up
People with this problem also raised
Related community dilemmas clustered by discussion consensus
Water leaking from roof corners and sidewalls
Improper shingle overlapping and flashing near corners cause water to wick sideways or get trapped under the upper layers instead of flowing downward. This leads to chronic water intrusion and rotted roof decking during heavy rain.
Roof or gutter contractors missed rotting fascia board
Hidden wood rot and sagging fascia are frequently discovered only after a new roof or gutter installation is complete. Because contractors often leave these structural issues unaddressed during the project, homeowners are left dealing with unexpected damage and costly disputes over who is responsible for the repairs.
Why is rainwater missing my gutters?
Gutters installed too high against the roof edge push shingles upward and cause rainwater to overshoot the trough entirely, pooling on the ground below. Fixing the issue requires lowering and repitching the gutter run so it sits flush beneath the roofline rather than pressing against the shingles.
How to stop roof runoff from missing the gutter and hitting the deck
Water streaming off the corner of a gabled roof often misses the gutter entirely and trickles down onto a lower deck or patio. Over time, this runoff causes leakage and water damage around the building corners.
Why are my new gutters leaking from behind?
Water overshoots the gap or leaks behind the gutter because of improper flashing, drip edge installation, or clogged foam guards, which prevents proper drainage off the roof. This runoff ultimately causes expensive water damage to the soffit that requires separate repairs.
How to tell if a gutter installation job is bad
Contractors sometimes leave large gaps in downspout adapters and poor connections that fail to direct water away from the foundation. This leaves homeowners uncertain whether they should withhold final payment or demand fixes to prevent basement water intrusion.