Said It Here

Should I replace a deformed copper pipe before pouring concrete?

Fixing a damaged water pipe now is essential because once the concrete is poured over it, access becomes impossible without jackhammering the floor later. Even though finding an urgent plumber is difficult, addressing the issue immediately prevents catastrophic leaks underneath finished concrete in the future.

OverviewLatest thread: Sep 2026
People affected2 accounts (1 forum)
Workarounds found1 items recorded
Discussion timelineSep 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/Plumbing · Sep 2026
Verification standards →

Core Friction Pattern

Analysis of 2 peer accounts across online developer and community forums reveals that “Should I replace a deformed copper pipe before pouring concrete?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
Leaving the deformed pipe as is and hoping it lasts without leaking under the concrete
Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Sep 2026)Indexed across peer discussions from Sep 2026 to Sep 2026
Evaluated against breaking changes & deprecations
  1. 1
    Leaving the deformed pipe as is and hoping it lasts without leaking under the concrete
    Did this help you?

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/Plumbing2 people · September 2026

“As this pipe is exposed now, I can see how deformed it is, but after they finish the work tomorrow, it will be impossible to cut and replace it. Is it a big issue? Should I somehow try to find a plumber at 7PM now?”source ↗

Apprehensive_I · r/PlumbingSep 2026· 1 upvotes

“Seems like someone whacked the crap out of that copper pipe. But in all honesty seems it’s exposed replace now. Don’t want to pour a lot concrete then X amount of years later you’ll have the jack hammered that concrete up”source ↗

HalfmanHalfBagle · r/PlumbingSep 2026· 1 upvotes

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

How wide of a trench should I be digging?

Determining trench width is difficult because it depends on an unclear pipe removal process and unstable walls that frequently cave in at the top. Beyond the punishing physical labor of digging through hard clay, people are left guessing about proper dimensions and how to handle underground plumbing connections like brazing or PEX fittings.

6 workarounds3 accounts · 2 forums

How to fix a leaking water pipe in a tight space

Repairing a pipe leak in a confined area like beneath attic ductwork requires choosing an appropriate temporary or semi-permanent fix to avoid high plumbing costs. However, recurring pinholes in older copper lines often lead to a frustrating cycle of repeated patches that eventually force a full-house replumbing.

289 workarounds143 accounts · 10 forums

Converting a bathtub to a shower with a 1 1/4 inch drain

Older homes often feature 1 1/4-inch drain lines, but modern building codes require a 2-inch pipe for a new shower installation. Upgrading this line requires breaking into old cast iron plumbing, which stops homeowners from finishing their bathroom renovations without major structural work.

2 workarounds2 accounts · 1 forum

What replacement material should I use for a corroded pipe nipple?

Corroded galvanized pipe sections and completely seized threaded flanges connected to copper or brass elbows leave zero room to work in tight wall spaces. This makes it difficult to remove the damaged parts and determine the proper replacement material to stop leaks.

12 workarounds5 accounts · 2 forums

Where to cut a cramped water heater cold line?

Tight clearance behind the water heater and connections close to the ground prevent pulling the unit out more than six inches from the wall. This leaves no obvious place to cut the cold water line while retaining enough pipe length to make a new connection.

7 workarounds5 accounts · 1 forum

How to replace a roof pipe boot with a cap

A pipe cap prevents a normal replacement boot from sliding over the pipe to seal holes leaking into the attic. Because split boots designed to wrap around the pipe are hard to find, homeowners resort to cutting a standard boot, duct taping it, and sealing it with roofing caulking.

16 workarounds8 accounts · 3 forums