Said It Here

Why won't my washing machine lid lock complete a cycle after replacement?

New lid lock assemblies often fail to complete cycles or register properly, sometimes leaving the lid stuck shut with a flashing red light. This prevents the machine from finishing wash loads and raises concerns about potential control board damage from jumping pins.

OverviewLatest thread: Nov 2026
People affected3 accounts (1 forum)
Workarounds found4 items recorded
Discussion timelineSep 2026 – Nov 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/appliancerepair · Sep 2026 – Nov 2026
Verification standards →

Core Friction Pattern

Analysis of 3 peer accounts across online developer and community forums reveals that “Why won't my washing machine lid lock complete a cycle after replacement?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
jumping pins to fake a closed lid signal

+3 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What the numbers show

Counted from the threads quoted below. How we count

  • People have been saying this in most months since September 2026.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Nov 2026)Indexed across peer discussions from Sep 2026 to Nov 2026
Evaluated against breaking changes & deprecations
  1. 1
    jumping pins to fake a closed lid signal
    Did this help you?
  2. 2
    replacing the lid switch assembly with non-OEM parts
    Did this help you?
  3. 3
    Replacing the main control board at the same time as the door lock
    Did this help you?
  4. 4
    Soldering and replacing the broken triac and resistors on the mainboard
    Did this help you?
Tried another approach not listed above?+ Share your workaround ↑

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/appliancerepair3 people · September 2026 – November 2026

“I cleared the fault codes and I'm still getting fault code 23 (critical door lock failure) after trying a spin test.”source ↗

“Initial symptom was that the door would not unlock. Now it won't lock either on Test 14 for spin.”source ↗

“While running Test 13 for door lock switch, I only get 59 volts with the door closed and 1 volt with the door open. I should be reading 120 volts based on the manual.”source ↗

Curious-Addition-770 · r/appliancerepairNov 2026· 2 upvotes

“I ordered a non-original lid lock switch assembly off Amazon and, in the meantime, jumped 2 pins to get the washer to register it was closed so I can finish the load of laundry.”source ↗

“I installed the new assembly, and it reads when it's opened or, but it doesn't complete a cycle.”source ↗

“Could I have fried the board from jumping the pins? Even though everything else is functioning?”source ↗

TimeApprehensive3994 · r/appliancerepairSep 2026· 1 upvotes

“The lid is stuck. When I plug it up nothing happens except the red light for the locked lid comes on and I can't get it open.”source ↗

“Trying to open the lid the light will flash and a click sound can be heard but nothing else.”source ↗

TerryGonards · r/appliancerepairSep 2026· 1 upvotes

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

Front panel wont open on General Electric Stackable Laundrycenter

The front panel on the laundry center won't open because the release clips or latch mechanisms are stuck or hidden, preventing users from accessing the interior despite trying tools like a 5-in-1 tool or butter knife.

1 workaround2 accounts · 1 forum

Washing machine leaking from the door seal even after replacing gasket

A damaged or improperly seated rubber boot seal causes water to leak around the washing machine door. If replacing the gasket fails to stop the leak, the tub alignment, door latch, or spring clamp tension may be off, preventing a proper watertight seal during cycles.

32 workarounds14 accounts · 4 forums

How to fix a snapped refrigerator door hinge or drawer knob

When a plastic hinge pin or drawer knob snaps off and a replacement part cannot be found, gluing it rarely holds up under daily use because of the constant torque and cold temperatures. Instead, you can reinforce the joint by drilling a small pilot hole and inserting a metal screw or pin as a permanent core to bear the weight.

3 workarounds2 accounts · 2 forums

Can a chipped washing machine drum be repaired?

Chipped washing machine drums can sometimes be repaired using an appliance touch-up paint or enamel kit if the damage is only cosmetic, but rust or structural leaks usually require replacing the drum. Leaving a chip unaddressed can cause clothes to snag and rust to bleed onto fabrics during washes.

14 workarounds10 accounts · 2 forums

Why won't my washing machine front panel come off?

Even after removing the obvious inner and outer screws, the front panel often remains stuck at the bottom middle. Online video tutorials frequently show screw locations that do not match the actual machine, leaving people unable to find the hidden connections. This prevents them from taking off the housing to perform basic maintenance like cleaning the lint trap.

4 workarounds2 accounts · 1 forum

Why won't a replacement door handle click into place?

Replacement door handles often fail to align or click into place because of misaligned strikers, confusing extra plastic components, or underlying hardware issues. Struggling with these misalignments leaves people frustrated for hours over what looks like a simple DIY fix.

10 workarounds7 accounts · 3 forums