Can you use JB Weld on a cut sway bar or metal car part?
Accidentally cutting into a suspension component like a sway bar or rear stabilizer link leaves people wondering if using steel-reinforced epoxy like JB Weld can safely fill the gap and hold. Relying on makeshift fixes when the right tools or replacements aren't immediately available creates uncertainty about whether the part will hold under stress or weaken the vehicle.
Core Friction Pattern
Analysis of 3 peer accounts across online developer and community forums reveals that “Can you use JB Weld on a cut sway bar or metal car part?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.
+4 alternative community-tested workarounds cataloged below.
What people tried
Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.
Found another way around this?
Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.
Can you use JB Weld on a cut sway bar or metal car part?
- 1Applying JB Weld or SteelStik epoxy puttyDid this help you?
- 2Using a TIG or MIG welder to properly repair the cutDid this help you?
- 3Hammering it back using a block of wood and a hammerDid this help you?
- 4Leaving it alone if it holds airDid this help you?
- 5Buying a new wheel or tire sensor if damagedDid this help you?
In their words
Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.
“Noticed this dent on my wheel just wanted some advice if it’s safe to leave as it is.”source ↗
“Was going to just use a hammer and punch but didn’t know if that would weaken it at all”source ↗
“Gave mine a decently small whack and fucked my TPMS.”source ↗
“During taking seized rear stab links off i cut the bar by accident (somewhat), will jb weld steel quickset filled in that gap hold?”source ↗
“Its all i got right now unfortunately, my sway bars are pretty old anyways. Just hope it holds its steelstik jb weld”source ↗
Where this came up
People with this problem also raised
Related community dilemmas clustered by discussion consensus
Can you fix a deep car body crease yourself?
Fixing a crease at home is difficult because body lines require precise metal reshaping, and tricky paint colors like silver are hard to match without professional equipment. Attempting it yourself risks making the damage look worse or wasting time and materials on a part that might need professional replacement.
How to fix loose metal roof trim that won't stay in
When wind bends metal roof edge trim away, simply pushing it back into the existing holes fails to secure it in place. This leaves an exposed gap that risks water running into the structure between the flashing and the wall.
How to fix a bent basketball hoop pole
Fixing a bent or kinked structural metal pole like a basketball hoop support often involves high safety risks, especially if power lines or electrical components are nearby. Because structural integrity is compromised, straightening a severe kink can cause sudden failure or electrocution if not properly evaluated.
How to fix small rust spots on a car yourself
Small rust spots often appear as bubbling paint where moisture has gotten underneath the metal. Treating these spots early prevents the corrosion from spreading further across the body panels, saving you from expensive professional repair bills on your first car.
How to fix a large hole in metal siding
Patching gaps in metal siding prevents water from seeping in and rotting the underlying wood. However, beginners to home repair often leave these holes exposed—from small punctures near gutters to two-foot cutouts from electrical upgrades—because they do not know what materials to use for the patch.
Why does my exhaust manifold gasket keep blowing out?
Exhaust manifold gaskets fail repeatedly because corrosion pitting on the engine cylinder head creates micro-gaps that no gasket can seal long-term. This continuous leakage prevents the exhaust system from holding pressure and forces constant gasket replacements.