Said It Here

How to get a broken charging tip out of an appliance

When the tip of a plug snaps off inside an appliance, it completely blocks the connection and leaves you unable to tell what's wrong with the internal contact. This prevents the device from charging and makes standard cable replacement impossible without first removing the lodged piece.

OverviewLatest thread: Sep 2026
People affected2 accounts (1 forum)
Workarounds found3 items recorded
Discussion timelineSep 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/askanelectrician · Sep 2026
Verification standards →

Core Friction Pattern

Analysis of 2 peer accounts across online developer and community forums reveals that “How to get a broken charging tip out of an appliance” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
Splicing or soldering the thin wires directly to the board inside the device

+2 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Sep 2026)Indexed across peer discussions from Sep 2026 to Sep 2026
Evaluated against breaking changes & deprecations
  1. 1
    Splicing or soldering the thin wires directly to the board inside the device
    Did this help you?
  2. 2
    Bypassing the battery and wiring a DC supply directly
    Did this help you?
  3. 3
    Testing with another wire or plug
    Did this help you?

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/askanelectrician2 people · September 2026

“The annoying thing is that I can't tell.”source ↗

Bareknuckleblaze · r/askanelectricianSep 2026· 2 upvotes

“The tip of the plug broke off in the appliance.”source ↗

lurkersforlife · r/askanelectricianSep 2026· 1 upvotes

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

Can I drive with a melted diagnostic port wire?

Accidentally short-circuiting the diagnostic port ground cable can melt the wire insulation and leave exposed copper. Whether it is safe to drive depends on how extensive the short was and what else the melted harness connects to, but driving with exposed or damaged wiring risks further electrical shorts before a replacement harness can be installed.

33 workarounds17 accounts · 6 forums

How to fix a corroded speaker wire connector without drilling out rivets

Corrosion can cause speaker wires to break right off the connector, but drilling out the factory rivets to replace the terminal is unnecessary. Instead, you can buy a replacement pigtail harness and splice it directly into the existing wires to restore the connection.

5 workarounds4 accounts · 3 forums

Forgot how to wire a part after taking it off

Without a reference photo, rewiring a replaced component requires tracing wires back to their original terminals using user manuals, wiring diagrams, or device schematics. Guessing connections can cause electrical shorts, blown fuses, or permanent damage to the equipment.

8 workarounds8 accounts · 4 forums

How to get twists out of a coiled cable

Cables frequently develop deep torsion and twists from being coiled even when they have no cuts, cracks, or bulges. This severe twisting prevents the wire from straightening out and looking like a new cable.

9 workarounds4 accounts · 3 forums

How to fix cut vehicle wires

When wires in a vehicle are accidentally cut or pulled out during DIY repairs or arguments, the car becomes unable to run. Fixing this requires identifying the damaged lines and reconnecting them properly to restore electrical continuity.

8 workarounds5 accounts · 2 forums

How to fix a pulled out threaded insert in thin aluminum

Instead of buying a new engine head, an automotive machinist can often repair the hole using a Time-Sert or an extended 14mm Big-Sert designed specifically for failed helicoils. This provides a cost-effective solution when mechanics claim the cylinder aluminum is too thin for a standard insert, letting you secure the bolt and eliminate the rattle without junking the part.

6 workarounds2 accounts · 2 forums