Said It Here

What to do with excess pipe sticking out of the wall

The cover ring often does not provide enough coverage to hide the exposed plumbing. You are left having to cut off the excess, embed the wall fitting deeper, or lose valuable room space framing around it when finishing a basement.

OverviewLatest thread: Nov 2026
People affected2 accounts (1 forum)
Workarounds found5 items recorded
Discussion timelineOct 2026 – Nov 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/Plumbing · Oct 2026 – Nov 2026
Verification standards →

Core Friction Pattern

Analysis of 2 peer accounts across online developer and community forums reveals that “What to do with excess pipe sticking out of the wall” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
Considering cutting off the excess threaded pipe

+4 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Nov 2026)Indexed across peer discussions from Oct 2026 to Nov 2026
Evaluated against breaking changes & deprecations
  1. 1
    Considering cutting off the excess threaded pipe
    Did this help you?
  2. 2
    Embedding the 90-degree wall fitting deeper into the shower wall
    Did this help you?
  3. 3
    Chop out the existing wye fitting and install a double wye.
    Did this help you?
  4. 4
    Raise all the drainage pipes and tie them in vertically.
    Did this help you?
  5. 5
    Raise the drainage and drop it into a wye on its back.
    Did this help you?
Tried another approach not listed above?+ Share your workaround ↑

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/Plumbing2 people · October 2026 – November 2026

“What do I do with this? Do I cut off the excess?”source ↗

sandolllars · r/PlumbingOct 2026· 1 upvotes

“The ring is only 4mm so not much coverage there. I guess I have to embed the wall fitting deeper.”source ↗

sandolllars · r/PlumbingOct 2026· 1 upvotes

“Builder has this configuration made for the final drainage/cleanout. I want to finish the basement and don’t want to lose a bunch of space framing around it. What are my options to bring it in closer to the wall?”source ↗

LithiumLemming · r/PlumbingNov 2026

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

Water leaking out of the wall during a shower

Water emerges from multiple locations on the first floor beneath a tub whenever someone takes a shower, often caused by a short, improper CPVC pipe connection. This sudden leak stops normal bathroom use and requires inspecting and repairing the plumbing behind the wall.

6 workarounds2 accounts · 2 forums

How to fix a PVC drain pipe broken flush against the wall

When a PVC pipe breaks completely flush with or recessed inside an exterior wall, standard couplings cannot be glued onto the outside. Using a rotary tool to slightly widen the inside diameter of the remaining pipe allows you to slide and glue a smaller fitting directly on the inside. This lets you complete the repair from the outside without having to tear open the wall.

9 workarounds7 accounts · 2 forums

Is a gap around exterior pipes acceptable?

Builders may claim a half-inch hole is acceptable, but this leaves a broken seal where daylight visibly passes right through from the outside. Instead of getting a properly fitted pipe, homeowners with no handy skills are left worrying about how to fix the gaping hole in their siding.

4 workarounds2 accounts · 2 forums

Can you move a waste pipe inside a wall near outlets?

Relocating a waste pipe connected to a macerator pump inside a stud wall requires careful management of both structural framing and proximity to electrical sockets and dryer vents. Squeezing pipes into tight wall cavities often creates conflicts with studs, plug sockets, and exhaust ports, making safe alignment difficult.

1 workaround2 accounts · 2 forums

What to do with old water pipes after removing a fixture?

Leaving inactive water lines open creates serious risks of accidental leaks, child tampering, and stagnation issues like dead legs. You need to properly secure and cap off these leftover secondary pipes using appropriate fittings or soldering to prevent future damage.

11 workarounds7 accounts · 2 forums

How to fix a gap behind an outlet faceplate

Changing an outlet often rips off the silicone putty used to shape uneven surfaces, leaving no secure way to attach the faceplate without a gap. Additionally, oversized box holes can prevent traditional outlet screws from holding the cover properly.

13 workarounds5 accounts · 4 forums