Said It Here

What to do with extra long washing machine hoses?

New washing machine supply hoses often come in standard lengths that end up too long and awkwardly looped behind the appliance. These extra loops can create confusing visual concerns about water flow restrictions and kinks, leaving installers unsure if they need shorter hoses or how to safely manage the excess length without damaging the machine.

OverviewLatest thread: Sep 2026
People affected2 accounts (2 forums)
Workarounds found5 items recorded
Discussion timelineSep 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/appliancerepair, r/AskMechanics · Sep 2026
Verification standards →

Core Friction Pattern

Analysis of 2 peer accounts across online developer and community forums reveals that “What to do with extra long washing machine hoses?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
coil up the extra length and secure them with zip ties

+4 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Sep 2026)Indexed across peer discussions from Sep 2026 to Sep 2026
Evaluated against breaking changes & deprecations
  1. 1
    coil up the extra length and secure them with zip ties
    Did this help you?
  2. 2
    buy shorter hoses
    Did this help you?
  3. 3
    trimming the hose to reduce the turn apex
    Did this help you?
  4. 4
    using lubrication to help slide it further onto the standoff
    Did this help you?
  5. 5
    pushing it down more to ensure it is fully seated
    Did this help you?
Tried another approach not listed above?+ Share your workaround ↑

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/AskMechanics1 person · September 2026

“The old one came off in pieces after a 20 minute fight, and the new one doesn't wanna go any farther than this. It doesn't seem super linked, but it is more than the old one.”source ↗

Funnybombninja · r/AskMechanicsSep 2026· 3 upvotes
r/appliancerepair1 person · September 2026

“I’m not sure if I should put less curly hoses on. The way it looks I just imagine the water having a tough loopy time making to it the washer ?”source ↗

“Saw that 3/4 hoses damaged the machine making it work to get water in but not sure any help would be appreciated”source ↗

Ok-Turnip-9035 · r/appliancerepairSep 2026

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

How to store a stiff hose without tangling

Stiff pressure washer and heavy-duty garden hoses naturally twist and kink, causing standard storage methods to fail. Hanging them on hooks looks messy, bins require complete untangling before every wash, and commercial winders often have drums too small that immediately kink the line. Dealing with this constant mess makes the actual washing process frustrating and drives people to consider just buying a less stiff hose entirely.

12 workarounds6 accounts · 2 forums

Washing machine drain pipe keeps leaking after putting back on

Flexible waste pipes often sit loosely inside under-sink connections even after being pushed in and tightened. Without a proper clamp, rubber seal, or connector piece to lock the joint in place, water continuously leaks out at the connection point.

2 workarounds3 accounts · 2 forums

Where to put a hose clamp to prevent a leak

It is difficult to know whether to put the clamp immediately after the first flare or pull it forward to anywhere the hose snugs over. This uncertainty leaves people worried that the way it is placed right now will cause a leak.

6 workarounds2 accounts · 2 forums

How to hook up a dishwasher drain hose under the sink

Connecting a dishwasher drain hose safely requires dealing with an under-sink outlet that powers the appliance while you are trying to test the setup. Uncertainty about the grey hose connection and proximity to electricity makes it difficult to verify the plumbing is right without creating a hazard.

20 workarounds12 accounts · 3 forums

How to fix a sink drain pipe that is too short

Drain pipes that are a fraction of an inch too short lack the proper engagement depth to stay securely connected under vibration or pressure. This causes the slip joint to periodically work loose and leak, forcing constant manual checks and makeshift fixes.

13 workarounds5 accounts · 1 forum

How to get a stuck hydraulic hose loose without breaking it

Stuck hydraulic hoses often seize due to rust, tight compression fittings, or a lack of leverage to generate enough torque. This prevents you from finishing basic repairs or replacements without making an unnecessary trip to the hardware store for specialized tools.

27 workarounds11 accounts · 3 forums