Said It Here

Applying roof coating over old flaking or thick layers

Old roof layers often create uneven surfaces that keep people from applying a new coating smoothly or getting it flush against adjoining walls. Existing coatings may also have unknown textures or asphalt reinforcement that cannot easily be cut down, and flaking can make a tired-looking roof deck harder to coat over.

OverviewLatest thread: Nov 2026
People affected2 accounts (1 forum)
Workarounds found4 items recorded
Discussion timelineNov 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/Roofing · Nov 2026
Verification standards →

Core Friction Pattern

Analysis of 2 peer accounts across online developer and community forums reveals that “Applying roof coating over old flaking or thick layers” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
Hire an HVAC company to relocate the equipment lines to a better place.

+3 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Nov 2026)Indexed across peer discussions from Nov 2026 to Nov 2026
Evaluated against breaking changes & deprecations
  1. 1
    Hire an HVAC company to relocate the equipment lines to a better place.
    Did this help you?
  2. 2
    apply a 100% silicone coating
    Did this help you?
  3. 3
    remove and resurface if the existing layer is silicone
    Did this help you?
  4. 4
    pressure wash and apply a deck coating if it is not silicone
    Did this help you?
Tried another approach not listed above?+ Share your workaround ↑

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/Roofing2 people · November 2026

“I have a small roof deck/patio above indoor living space. It's generally in good condition and there is no leaking. But, it's looking a little tired with some flaking and I want to add a surface coating.”source ↗

“The current coating is pinkish in color and has a little texture (sand?). It doesn't feel like silicone, but I'm not sure what it is.”source ↗

SteveB2551 · r/RoofingNov 2026· 3 upvotes

“the old elastomeric juts out about two inches from the plywood wall and is too thick with some kind of asphalt roll reinforcement to be reduced to the point where it is flush with the plywood to allow new elastomeric to be properly applied and ajoin it.”source ↗

babel-op · r/RoofingNov 2026· 1 upvotes

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

How to clean dark roof stains without ruining the shingles

Dark roof stains caused by environmental moisture can usually be treated with specialized chemical concentrates instead of a full roof replacement. However, improper cleaning techniques can strip the protective granules and shorten the lifespan of the shingles, leaving homeowners torn between whether to clean now or risk damaging the roof.

19 workarounds10 accounts · 1 forum

Can you put wall filler straight over exposed joint compound?

Exposing the underlying mud while scraping away old paint or caulk means you are dealing with a water-soluble surface. Applying a primer or sealer first prevents the moisture in the wall filler from dissolving the exposed mud, which stops the patch from bubbling, failing to adhere, or washing out.

7 workarounds4 accounts · 2 forums

How to install drip edge on an existing roof

Installing a drip edge on an existing shingle roof requires finding reliable instructional videos, as many homes are built without one. Homeowners trying to add this flashing before putting up gutters often have to search for the correct method to retrofit it properly.

10 workarounds8 accounts · 1 forum

What cap sheet lasts longest over an old smooth hot roof?

Figuring out the right materials for a flat roof is tricky, even for DIYers who have successfully installed shingles before. Online tutorial videos often fail to clarify exactly what to use for the underlayment or which roll-on cap sheet is the most durable option to apply.

3 workarounds3 accounts · 2 forums

How to seal concrete when it rains every day before winter

Continuous daily rain leaves no window of dry time required for concrete sealers to properly cure before freezing winter temperatures arrive. This forces homeowners to either risk an improper application or abandon the job entirely and wait until spring.

2 workarounds2 accounts · 1 forum

How to temporarily waterproof a damaged roof until replacement

Finding short-term waterproofing methods prevents interior mold growth and further water damage while waiting months for a full roof replacement. Improvised fixes like adding new concrete layers often fail to stop leaks completely, making reliable temporary patches essential without risking worse damage.

79 workarounds29 accounts · 4 forums